Rochester Premier Insulation: Spray Foam, Attic & Crawl Space Insulation
Rochester Premier Insulation installs spray foam, attic, and crawl space insulation in Rochester, MN. Ice at the eaves, rooms that never catch up with the thermostat, and attic fill that has settled off the joists are the usual reasons people call. We can help with lowering heating bills, warmer floors, fewer drafts, and less heat loss through the attic.
Open-cell and closed-cell foam, cellulose, and fiberglass each have a place. We'll tell you which one fits after we look at your attic, the walls, the crawl, and how the house is leaking air. Request a free estimate below.
Get My Free EstimateGet Your Free Estimate
We'll get back to you within one business day.
Rochester's Top Insulation Contractor
Free estimates
After we look at the attic, walls, and crawl
Homes and commercial
Spray foam, attic, and crawl on one visit when needed
Air sealing with the insulation
Built into the job, not an afterthought
Honest tear-out vs top-off
We say which old fill should come out before quoting
Rim joists and crawl walls
In scope with the insulation job
Clean sites, Rochester-area
Byron, Stewartville, Pine Island, Kasson - walkthrough before we call it done
Spray Foam, Attic & Crawl Space Insulation
Spray Foam Insulation
Two-pound closed-cell or half-pound open-cell, sprayed to the roof deck, rim joist, or a wall cavity. Closed-cell adds a vapor retarder and more R-value per inch. Open-cell fills odd bays and stays vapor-open. Both air-seal as they expand. That's the part that actually changes how the room feels.
Attic Insulation
Loose-fill over the ceiling plane, or foam against the roof deck when the attic is coming into the conditioned envelope. We check baffles at the soffits so new fill does not choke intake. Depth follows the R-value your job needs, not a one-size bag count. After a hard Minnesota winter, a thin attic shows up fast once the heat is on.
Blown-In Insulation
Cellulose or fiberglass blown over an attic floor, or dense-packed into closed wall cavities through small holes. Dense-pack resists settling better than a loose dump. We run the hose to depth, then patch and paint the access holes. This is the usual call when you want more R without opening every drywall bay.
Wall Insulation
Retrofit walls get dense-pack cellulose or injected foam through drilled holes. New walls can take batts, blown fill, or foam in the cavity. We do not open every wall as a default. You confirm whether interior or exterior access is allowed. A full cavity also cuts sound transfer, but that is a side effect, not a separate product on this card.
Crawl Space Insulation
Your crawl can be insulated at the floor joists, or the walls can be brought inside the thermal envelope with foam or rigid board and a sealed vapor barrier on the dirt. Rim joists are part of that job. You confirm local code for a closed crawl versus a vented one.
Insulation Removal
Old cellulose, fiberglass, and vermiculite-looking fill come out with a vacuum truck when they are wet, contaminated, or too packed to top off. Removal is ask-not-automatic. We look at the material before quoting a tear-out. New fill goes in after the cavity is dry and attic-floor air leaks are sealed.
Commercial Insulation
Office & Commercial Buildings
Offices, clinics, and storefronts. Evenings or weekends keep the floor open when that is what your schedule needs. We spec foam, blown fill, or batts from the assembly, not a one-product pitch. Cleanup is part of the job.
Warehouse & Industrial
High bays, metal roofs, and conditioned shops. The usual ask is a more even temperature at floor level and less condensation under the roof. Access equipment and after-hours scheduling are part of the estimate.
Metal Buildings
Pole barns, shops, and pre-engineered metal buildings. Liner systems, foam to the skin, or a mix. Condensation on the interior face of metal is the usual complaint. Fastener pattern and existing liner stay until we see your building. This is a customer type, not a second spray-foam card.
Insulation Types & R-Values
Spray Foam vs Blown-In vs Batt
Foam air-seals and insulates in one pass. Blown-in is the usual attic-floor and retrofit-wall product. Batts fit open stud bays when the cavity is empty and square. Closed-cell foam carries more R per inch than cellulose or fiberglass. Your assembly and access decide the product, not a ranking of which is best.
Fiberglass, Cellulose & Mineral Wool
Fiberglass shows up as batts or blown fill. Cellulose works well for denser wall packs and older attic floors. Mineral wool is a stiffer batt with a higher melting point when that fits the bay.
Open-Cell vs Closed-Cell Foam
Open-cell is softer, fills irregular bays, and stays vapor-open. Closed-cell is denser, adds more R per inch, and can serve as a Class II vapor retarder at the thickness the manufacturer lists. Mix ratio, substrate temperature, and thickness get checked on site. DIY kits are a different product than a sprayed assembly.
What Insulation Problems Do We Help With?
Ice Dams
Heat leaking into a cold attic melts snow from below. Water runs to the eave, refreezes, and backs up under the shingles. Air sealing at the attic floor, enough ceiling-plane insulation, and clear soffit baffles are the usual fix.
Attic Mold
Mold on sheathing often tracks with a leaky attic floor, poor baffles, or a wet roof. We look at the wet material, the ventilation path, and whether the fill has to come out before new insulation goes in. Widespread growth needs a mold-remediation contractor. That is a different trade.
How Much Does Insulation Cost in Rochester, MN?
Published 2026 buyer guides put blown-in attic work around $0.90 to $3.00 per square foot. Spray foam runs higher, roughly $2 to $6 per square foot depending on open-cell versus closed-cell. Your quote follows the assembly, not a city average.
Depth, access, air sealing, and whether old fill has to come out move the number more than the city name does. A site visit is the only way to get a firm figure.
Rebates and energy-program dollars exist in Minnesota. You confirm current programs. We do not list dollar amounts here.
| Service | Typical Range |
|---|---|
| Blown-in attic insulation, installed | $0.90 to $3.00 per sq ft |
| Attic insulation, typical project | varies with depth and tear-out |
| Open-cell spray foam, installed | $2.20 to $4.10 per sq ft |
| Closed-cell spray foam, installed | $3.00 to $6.00 per sq ft |
| Wall dense-pack or injected foam | quoted after access is confirmed |
| Old insulation removal | ask, not automatic |
Ranges reflect published 2026 buyer guides for blown-in and spray foam (HomeGuide, Angi/HomeAdvisor, RemodelCalculators) and are not an estimate for this business's rates.
What to Expect When You Hire Rochester Premier Insulation
- 01
On-site estimate
We look at your attic, walls, and crawl, note existing fill, and say whether old material should come out before quoting.
- 02
Air leaks and depth
Bypasses at the attic floor, can lights, and chases get called out. Depth and product follow the assembly, not a bag count.
- 03
Material selection
Foam, cellulose, or fiberglass. Open bays versus dense-pack. You pick from what actually fits the job.
- 04
Prep and protection
Access, containment, and a path for the hose or spray rig. Belongings in the work area get covered or moved.
- 05
Install
Fill, foam, or batts go in to the depth on the estimate. Baffles stay open. Rim joists and obvious leaks get sealed with the insulation.
- 06
Final walkthrough
We walk the work with you before calling the job done. Patch and paint of access holes is part of a wall pack unless the estimate says otherwise.
Insulation Installation in Byron, Stewartville, Pine Island & Kasson
Rochester Premier Insulation is based in Rochester, MN. Byron, Stewartville, Pine Island, and Kasson are in range. Freeze-thaw winters and older housing stock are why attic depth and crawl moisture show up on so many estimates out here.
- Rochester, MN
- Byron, MN
- Stewartville, MN
- Pine Island, MN
- Kasson, MN
Insulation FAQs
Do you install spray foam and blown-in insulation?
Yes. Spray foam, blown-in cellulose or fiberglass, and batts are all in scope. The assembly decides which one we recommend.
Is the old insulation removed with the new install?
No, not automatically. Wet, contaminated, or packed fill usually comes out. Clean, dry fill can often stay and get a new layer on top. Ask so it shows up on the estimate.
Will more attic insulation stop ice dams?
Often it helps, but only if heat is not leaking into the attic in the first place. Air sealing at the attic floor and clear soffit baffles matter as much as the new depth.
Do you insulate walls without tearing off the drywall?
Yes. Dense-pack and injected foam go in through small holes. We patch those holes. Full tear-off is a different job and only when the wall is already open.
How long does a typical attic job take?
A straightforward blown-in attic is often a day once we are on site. Foam, wall packs, and removal add time. We give a range after we see the house, not a same-day promise.
Do you work on crawl spaces and rim joists?
Yes. Floor joists, crawl walls, and rim joists are in scope. A closed crawl versus a vented crawl is your call with local code, not a default we impose.
Why are my floors cold in winter, and why won't some rooms warm up?
Cold floors often track with a thin or missing crawl insulation, leaky rim joists, or heat that rises and leaves the living space. Rooms that never catch the thermostat usually have air leaks, low attic depth, or both. We look at the attic, the walls, and the crawl together so the estimate matches what your house is actually doing.
Will better insulation lower my heating bills?
It often helps when air sealing and enough depth are part of the same job, because less heat escapes and the furnace or boiler cycles less. That is not a guarantee of a dollar amount. Your bill also moves with thermostat habits, equipment age, and utility rates.
Do crawl spaces need a vapor barrier, and what about moisture?
A sealed vapor barrier on the dirt is common when a crawl is brought inside the thermal envelope. Moisture, standing water, and damaged fill should be called out before new insulation goes in. You confirm with local code whether a closed crawl or a vented crawl fits your house.
Do I need a permit for insulation work in Rochester or Olmsted County?
Permit rules depend on the scope and on what the city or county requires for that address. Some attic top-offs need nothing; other assemblies may. You confirm current requirements with Rochester or Olmsted before work starts. We do not invent permit rules on this site.
Are there Minnesota energy rebates or utility programs for insulation?
Minnesota utilities and state energy programs sometimes offer rebates for attic, wall, or air-sealing work. Programs change, and dollar amounts are not fixed here. You confirm what is current with your utility or a Minnesota energy program before counting on a rebate.
Get an Insulation Estimate in Rochester
Tell us whether it is a house or a workplace. We will look at the attic, the walls, and the crawl, then send a free estimate.